8.37. Rotate Colors

8.37.1. Overview

Figure 16.215. Example for the Rotate Colors filter

Example for the “Rotate Colors” filter

Original image

Example for the “Rotate Colors” filter

Filter Rotate Colors applied


Colormap Rotation lets you exchange one color range to another range.

8.37.2. Activating the filter

This filter is found in the image window menu under ColorsMapRotate Colors.

8.37.3. Main Options

Figure 16.216.  Main Options of the Color Map Rotation filter

Main Options of the “Color Map Rotation” filter

You have there two color circles, one for the From color range and the other for the To color range:

From

The Color Circle: Two axis to define From range. The curved arrow in angle lets to recognise From axis and To axis of range. Click-drag these axis to change range.

Switch to Clockwise/Counterclockwise: Sets the direction the range is going.

Change Order of Arrows: Inverts From and To axis. This results in an important color change as colors in selection angle are different.

Select All selects the whole color circle.

From and To boxes display start axis and end axis positions (in rad/PI) which are limiting the selected color range. You can enter these positions manually or with help of arrow-heads.

To

This section options are the same as From section ones.

8.37.4. Gray Options

Figure 16.217. Base image for Gray Options

Base image for Gray Options

Three sectors are defined for Red, Green and Blue with different saturations. Gray and White colors are represented (0% Sat).


In this tab, you can specify how to treat gray. By default, gray is not considered as a color and is not taken in account by the rotation. Here, you can convert slightly saturated colors into gray and you can also convert gray into color.

Gray Color Circle

At center of this color circle is a small define circle. At center, it represents gray. If you increase gray threshold progressively, colors with saturation less than this threshold turn to gray.

Then, if you pan the define circle in the color circle, or if you use input boxes, you define Hue and Saturation. This color will replace all colors you have defined as gray. But result depends on Gray Mode too.

Gray Mode

The radio buttons Treat As This and Change As This determine how your previous choices will be treated:

  • With Change to this, gray will take the color defined by the define circle directly, without any rotation, whatever its position in the color circle.

  • With Treat as this, gray will take the color defined by the define circle after rotation, according to From and To choices you made in the Main tab. With this option, you can select color only in the From sector, even if it is not visible in Gray tab.

Figure 16.218. Gray Mode

Gray Mode

The small circle is on yellow and mode is Change to this. Blue has changed to yellow. Note that Gray and White did so too.


Gray Threshold

Figure 16.219. Gray Threshold

Gray Threshold

Gray-threshold is 0.25: the blue sector (sat 0.25) has turned to Gray (Note that Gray and White, that are 0% Sat., are not concerned).


You specify there how much saturation will be considered gray. By increasing progressively saturation, you will see an enlarging circle in color circle and enlarging selected areas in Preview if Continuous update is checked. In a black to white gradient, you can see enlarging color replacement as you increase threshold very slowly.

Black to White gradient, progressively filled with color, as threshold increases.

8.37.5. Previews

Original, Rotated

The Original preview displays a thumbnail of the original image and the Rotated preview displays color changes interactively, before they are applied to the Image.

Continuous Update

Continuous Update displays color changes continuously in the Rotated preview.

Area

In this drop down list, you can select between

  • Entire Layer: works on the whole layer (The image if there is no selection).

  • Selection: displays selection only.

  • Context: displays selection in image context.

8.37.6. Units

You can select here the angle unit used to locate colors in the Hue/Saturation circle. This choice is valid only for the current filter session: don't click on OK just after selecting unit, return to the wanted tab!