| 4.10. Unified Transform | ||
|---|---|---|
|
4. Transform Tools |  |
| 4.10. Unified Transform | ||
|---|---|---|
|
|
4. Transform Tools | |
This tool combines several tools: Rotate, Scale, Shear and Perspective, performing one or several of these actions at once in one single operation. Combining two or more options gives you almost infinite possibilities of transformation.
As the other transformation tools, this tool works on the active layer (default).
After selecting the Unified Transform tool in the toolbox, click on the image window. Several elements appear on the image window:
Several kinds of handles, on the edges:
Diamonds for shearing
Squares for scaling.
Small diamonds for changing perspective, in large squares for
Scaling.
Click and drag a handle to perform the action of the concerned tool
A circle with a cross inside at the center of the image window for the pivot. Click and drag this circle to move the pivot. It can be placed out of the image window, and even where you want on screen (but you can no longer see it, unless you enlarge the image window).
The mouse pointer comes with small icons which vary according to position:
On the layer: Move icon,
Outside the layer: Rotate icon,
On handles: Shear or perspective or Scale icon,
On rotation center circle: Move icon and Rotation icon.
The status bar, at the bottom of the image window, displays the name of the current tool.
When you click on the image window, also appears the Matrix new window:
where you find the Reset (very useful when testing), Cancel and Transform buttons. This matrix window appears out of the image or, if the image window is large enough, inside the image window. You cannot edit the values of this matrix, but you can note them to reproduce the same transformation later.
Readjust button: with this button, new in GIMP-2.10.10, you can readjust transform handles based on the current zoom level.
There are different possibilities to activate the tool:
From the image-menu: → →
The Tool can also be called by clicking the tool icon:
or by clicking on the Shift+L keyboard shortcut.
The available tool options can be accessed by double clicking the
Unified Transform tool icon.
![[Note]](images/note.png)
|
Note |
|---|---|
|
See Section 4.1, “Common Features” for a description of tool options that apply to many or all transform tools. |
Move: when this option is unchecked, moving the layer is smooth. Checking the option constrains movement to 45° from center.
Scale: when this option is checked, the aspect ratio is preserved.
Figure 14.147. Scale Constraint Option
Constrain not checked (no pivot)
Constrain checked (no pivot)
Rotate: default rotation is smooth. When this option is checked, rotation goes by 15° steps.
Shear: normally, to shear the layer, you drag the corresponding icon along a layer edge. If this option is unchecked (default), you may move away from this edge. If this option is checked, shear handles remain on this edge.
Perspective: normally, to change perspective, you drag the corresponding icon along a layer edge. If this option is unchecked (default), you may move away from this edge. If this option is checked, perspective handles remain on this edge or on a diagonal.
Scale:
Figure 14.149. Scale from pivot
From pivot not checked, constrain checked
From pivot and constrain checked
Shear: When this option is unchecked (default), the opposite edge is fixed and the pivot moves with shearing. When the option is checked, shearing is performed around a fixed pivot and the opposite side is sheared by the same amount, but in the opposite direction.
Perspective: when this option is checked, the position of pivot is maintained.
Figure 14.150. Perspective from pivot
From pivot not checked, constrain checked
From pivot and constrain checked
Snap: if this option is checked, the pivot snaps to center or to corners when it comes close to them.
Lock: locks pivot.
Key modifiers are active when an action (move, scale, rotate...) is selected. Hold on:
Shift to check all Constrain unchecked options and uncheck already checked ones if a transformation handle is selected, or, if the pivot is selected, to snap pivot to center or corner,
Ctrl to check all “From pivot” unchecked options and uncheck already checked ones.
